2021 STREET STOCK RULES

2021 STREET STOCK

The following specifications are prepared for Street Stock and are guidelines for construction of Street Stock class.  No expressed or implied warranty of safety shall result from publication of, or compliance with these rules.  They are intended as a guide and are in no way a guarantee against injury or death to participants, spectators or others. These specifications are for the Racing Season at Beckley Motorsports Park.  Management reserves the right to change them at any time.

ENGINE

362 CUBIC INCH MAX

MUST BE SAMES AS MANUFACTURE OF FRAME

OEM BLOCKS ONLY NO AFTERMARKET BLOCKS INCLUDING GM BOWTIE

BLOCKS MUST HAVE SERIAL NUMBERS

1 UNALTERED TWO BARREL CARBUATOR MAY REMOVE CHOKE AND REPLACE JETS ONLY

CAN USE HOLLEY CT4412 ONLY WITH ONLY ONE 1 INCH ADAPTER BETWEEN CARB AND INTAKE .07 GASKETS BETWEEN ADAPTER AND CARB AND INTAKE NO ULTRA OR ANY OTHER HIGH PERFORMANCE CARBS

OEM CAST IRON CYL HEADS ONLY MAX INTAKE MUST HAVE CORRECT VALVE SIZE FOR CASTING NUMBERS ON HEAD

STOCK SIZE VALVE SPRINGS NO BEEHIVE

STOCK DIAMETER VALVE SPRINGS

NO CUTTING OR MACHINING ANY NUMBERS

ANY NUMBERS REMOVED CONSIDER ILLEGAL

STOCK ROCKERS  OR ROLLER TIP ROCKERS OK, NO ROLLER ROCKERS 

HYD OR MECH CAMS ONLY NO ROLLER CAMS

NO LIGHT WEIGHT CRANK SHAFTS

2 BARREL CAST IRON INTAKE NO MODIFACTIONS OF ANY KIND MUST BE STOCK DIAMENTIONS NO ALUMINUM INTAKES

OEM EXHAUST MANIFOLDS OR 1 5/8 HEADERS ONLY 

MUST USE OEM STYL DISTIBUTOR NO HIGH PERFORMANCE IGNITION SYSTEMS

1 12 VOLT BATTERY NO 16 VOLT BATTERIES

GM SEALED 602 ALLOWED MUST BE MID EAST SEALS OR COMPATABLE MUST USE 2 BARELL CARBURATOR AS LISTED ABOVE WITH 2 TO 4 BARREL ADAPTER

TRANSMISSION MUST BE STOCK WITH ALL FORWARD AND REVERSE GEARS NO RACING TRANSMISSIONS

IF USING AUTOMATIC MUST HAVE FUNCTIONAL TORQUE CONVERTER

NO ENGINE OIL COOLERS

PUMP GAS OR RACING FUEL ONLY NO E 85 OR ALCHOL

NO VISIBLE AFTERMARKET PERFORMANCE PARTS

HOOD MUST FIT TIGHT FRONT AND REAR NO HOOD SCOOPS

NO ELECTRIC FUEL PUMPS, STOCK PUMPS ONLY NO PRESSURE REGULATORS

NO RACING FUEL PUMPS

NO VORTEC BOWTIE HEADS

STOCK CLUTCH PLATE WITH SPRINGS MIN 10.5 IN

ALL GASKETS MUST MATCH STOCK GASKETS

STOCK FLYWHEEL NO ALUMINUM FLYWHEELS

ENGINE BLOCKS WILL BE THE FOLLOWING GM 350 FORD 351 DODGE 360 MAX BORE IS 60 OVER

ANY COMPOUND TIRES ON CARS WITH 362 CUBIC INCH MAX 10 IN TREAD WIDTH MUST HAVE MIN OF 10 OUNCES OF BABY POWDER ON INSIDE OF TIRE

CARS MUST WEIGH MIN 3100 LBS

MAX COMPRESSION IS 175LBS AT ANY TIME

STOCK STROKE AND ROD LENGTH FOR SIZE OF ENGINE

NO LIGHTWEIGHT CRANKS OR LIGHT WEIGHT ROTATING ASSEMBLIES

INSPECTION PLUG IS MANDATORY ON OIL PAN

#1 SPARK PLUG NO FURTHER BACK THAN UPPER BALL JOINT

$3,000 ENGINE CLAIM RULE ON ALL ENGINES MUST FINISH ON LEAD LAP

IF YOU RACE, YOU ARE AGREEING TO THE ENGINE CLAIM RULE, NO EXCEPTIONS.

$350 CARB CLAIM RULE

CHASSIS

MADATORY MUST HAVE TOW CABLES OR CHAINS FRONT AND REAR OF CAR NO EXCEPTIONS

AMERICAN MADE CARS ONLY

OEM CHASSIS ONLY, NO TUBE CHASSIS CAR, NO CUTTING OF FRAME, ONLY EXCEPTION IS TO REPAIR FRAME DAMAGE FROM CENTER OF REAR HOUSING BACK

ALL CARS WITH SUB FRAMES CAN BE TIED TOGETHER, BUT MUST RETAIN STOCK REAR FRAME RAILS AND TRUNK.. CAN CUT CENTER OF TRUNK OUT FOR FUEL CELL.

AFTERMARKET BODIES OK BUT MUST LOOK FACTORY AND FIT IN STOCK LOCATION BE SAME AS FRAME MUST BE APPROVED BY TRACK TECH OFFICAL CHEVY TO CHEVY FORD TO FORD DODGE TO DODGE

FIBERGLASS HOODS ALLOWED

TUBULAR NON ADJUSTABLE UPPER CONTROL ARMS LEGAL BUT LOWER MUST BE STOCK AND IN STOCK LOCATION

SPINDLES WILL MATCH MANUFATURER OF CAR NO PINTO SPINDELS

NO ALUMINUM SHOCKS OR COILOVERS, NO ADJUSTABLE SHOCKS

ALL STEERING COMPONENTS WILL BE STOCK QUICK STEER IS OK

SUSPENSION MUST REMAIN IN STOCK LOCATION AND STOCK DIAMENTIONS NO THREE LINK REAR END UNLESS FACTORY 3 LINK

USE OF 9 IN REAR END LEGAL FLOATERS ALLOWED

NO QUICK CHANGE REAR ENDS OR TRANSMISSIONS

DISK BRAKES APPROVED ON REAR BUT MUST RUN OEM CALIPERS ONLY

ALL BRAKE COMPONENTS MUST BE STEEL OR FACTORY STAMPED ALUMINIUM

MUST HAVE WORKING BRAKES ON ALL 4 CORNERS

AFTERMARKET BRAKE PEDAL ASSEMBLY LEGAL MUST NOT BE ABLE TO ADJUST BRAKES FROM DRIVERS COMPARTMENT

WHEEL BASE WILL BE FACTORY LENGTH ON MAKE OF CHASSIS

NO TRACTION DEVICES

10 IN MAX STEEL WHEELS BEADLOCKS ALLOWED ON EVERY CORNER

MUST HAVE MIN 1 INCH LUG NUTS

SAFETY

FUEL CELL MUST BE IN A METAL CONTANER

MUST HAVE MIN 2 METAL STRAPS TO SECURE FUEL CELL 2 IN WIDE 1/8 IN THICK

MUST HAVE FIVE POINT HARNESS AND MUST CONNECT TO ROLL CAGE

BELTS CAN NOT BE OLDER THAN 3 YEARS FROM DATE OF MANUFATURING

MUST HAVE 2 LBS FIRE EXTINGUISHER WITHIN DRIVERS REACH

MIN 1 3/4 ROLL CAGE WITH 4 BARS IN DRIVER SIDE AND 3 IN PASSENGER SIDE

DRIVER SIDE IS REQUIRED TO HAVE A MIN 2FTX16 STEEL PLATE ON DRIVER SIDE ROLL BARS

4 BARS IN FRONT OF THE DRIVER IN WINDSHIELD

MUST HAVE DRIVE SHAFT LOOP

MUST HAVE FULL FIRE SUIT WITH FULL FACE HELMET

ALL CARS ARE TO BE REQUIRED TO BE ABLE TO REMOVE ANY ENGINE COMPONENTS AT ANYTIME  FAILURE TO DO SO WILL RESULT IN DISQUALIFICATION FOR THE NIGHT AND A 3 RACE SUSPENSION

PROTEST FEE $150

•Track has the right at anytime to make changes to the rules

•1-3 cars in any class could result in $50 tow money

•1-6 cars in a class will be adjusted pay for the night

The Absence of a specific rule does not imply approval, consent, or permission regarding the subject.  

IF IT IS NOT MENTIONED IN THE ABOVE RULES…DON’T TRY IT!  

Anyone disobeying these rules will be appropriately dealt with accordingly